✨Make your prints shine like the stars ✨
ALT TAB PLA Galaxy – Blabs Series is a glitter-infused PLA filament designed for stunning visual impact. Whether you’re making toys, gifts, cosplay props, or display models, this filament adds a cosmic shimmer to every layer — while staying easy to print and consistent in quality.
Product Features:
- Diameter: 1.75mm
- Material: PLA with glitter infusion
- Beginner-friendly: low warp, low smell, smooth extrusion
- Compatible with most 1.75mm FDM printers
- Best for indoor use – not suited for high-heat or outdoor exposure
❗ Compatibility Reminder❗:
This filament is compatible with Bambu Labs printers, including Bambu AMS and AMS Lite, as well as other 1.75mm FDM printers like Prusa, Creality, Anycubic, Elegoo Neptune, and more.
Each printer behaves differently depending on setup, firmware, and environment.
👉 Always run a test print before large jobs. Use the settings below as a guide and fine-tune for your machine.
🛠 Recommended Print Settings:
A QR code is printed on the filament box and the paper insert inside.
📲 Scan it to access our latest recommended print settings and usage guidance or click here.
📦 Recommended Storage & Moisture Handling:
To maintain the filament in optimal condition:
- Store in an environment with less than 40% relative humidity
- If you do not print often, keep the filament sealed or in a dry box between uses
If the filament is exposed to humidity and print quality is affected:
- Dry the filament at 55°C for 1 hour using a reliable filament dryer
- A recommended dryer is one with minimal temperature fluctuation, to avoid overheating
⚠️ Warning:
Overheating the filament can cause it to become extremely brittle or even fuse together into a solid roll.
We will not be liable for damage caused by improper drying or overheating.
💬 Frequently Asked Questions (FAQ)
-
Is it compatible with my printer?
✅ Yes! It works with Bambu Labs (AMS / AMS Lite), Prusa, Creality, Neptune, Anycubic, and most 1.75mm FDM printers. -
Does it really sparkle?
✨ Yes! The glitter is embedded in the filament and gives off a soft cosmic shine, especially under lighting. -
Is it beginner-friendly?
✅ Very. It prints like standard PLA — smooth flow, low warping, no strong odors. -
Do I need a heated bed?
🔧 It’s recommended. A bed temp of 55–60°C improves first-layer adhesion and consistency. -
Can I use it for functional parts?
✅ Yes, for light-duty functional parts like holders or brackets.
However, PLA is biodegradable, and in Singapore’s hot and humid climate, it will naturally degrade over time — especially if used outdoors or exposed to sunlight. Expect wear or brittleness within 1–2 years in such conditions. -
Is it AMS-compatible?
✅ Yes. This filament fits both Bambu AMS and AMS Lite systems. -
What’s special about Nebulae?
🌌 Nebulae is a dual-tone purple-blue blend with shimmering glitter. It shifts subtly under light, designed to give a galaxy-inspired effect. -
Do I need to dry the filament before use?
💡 Drying is not always required, but if print quality degrades due to humidity, drying at 55°C for 1 hour can restore performance. See storage guide above. -
Do you accept empty spools?
We currently do not collect empty spools, but they can be recycled via the blue bin as they are made from standard recyclable plastic. -
Will the spool get tangled?
❌ No – our spools are machine-wound in layered rows, making tangling during production impossible.
⚠️ Tangles only happen if the filament end is left loose during handling.
✔️ Always secure the filament end through the spool holes after use to prevent this.
